Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 208

Страница: 208 / 240

Appendix B

208

2008K Hemodialysis Machine Operator’s Manual Rev P

Creating Custom UF Profiles

Four custom UF profiles can be defined on the 2008K hemodialysis machine.

Step 1

To enter a custom UF profile, turn the machine on into Service Mode by pressing the

CONFIRM

key when prompted during the power up sequence.

Step 2

Touch the

Options

screen-button and then the

UF Profile

screen-button. The four UF

Profiles that can be modified will be displayed on the left side of the screen numbered from 5
– 8.

Step 3

Select the desired profile to modify and it will then be enlarged with each of the 12 segments
displayed in small edit boxes below the profile.

Step 4

One by one, touch the yellow numbered button below each of the 12 segments. Enter any
number from 0 to 100 using the numeric keypad or up and down arrow keys. Press

CONFIRM

when done.

Figure 71 – Creating Custom UF Profiles

Select the desired
profile and it will be
enlarged on the
screen.

Modify each of the
12 segments by
entering, with the
key pad, any
number from 0 to
100 in the box
below each
segment.

Содержание DIASAFE 2008 K

















































































































































































































































Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды