manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 177

Chapter 6—Alarms and Troubleshooting 

177 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Message 

Purpose of Message 

Type 

Action Required

 

RTD = Zero 

The RTD (Remaining Time on 
Dialysis) clock has counted down to 
zero. 

Warning 

Reset the alarm.  This message has alerted the operator that the 
preset time on dialysis has elapsed (RTD = 0:00). If prescribed 
treatment time has not been completed, the operator must take 
further action to comply with the prescribed treatment. 

Running Diasafe Test 

This message is advising the operator 
of the status of the Diasafe test 

Advisory 

Advisory only. No action is required. 

Running Online PHT 

This message is displayed when the 
online Pressure Holding Test is in 
progress. 

Advisory 

Advisory only. No action is required. 

Run Access Flow? 

This message is a prompt for the 
operator begin the Access Flow test. 

Warning 

To proceed now, press 

CONFIRM

.  To delay, press 

Escape

.  To 

cancel, go to the “Kt/V AF” screen and toggle the Access Flow check 
box to Off. 

Select Concentrate 

This message is a prompt for the 
operator to select a concentrate. 

Advisory 

To select a concentrate from the menu, use the 

 

or 

 

(

Up/Down) 

keys on the control panel to highlight the desired concentrate, and 
press 

CONFIRM

.  For more information, see Chapter 3, “Setting an 

Acid/Bicarbonate Type.” 

Select new goal or rate 

UF time is out of range. 

Dialog 

Message 

Enter a new UF Goal or reduce UF time. 

Select new Goal or Time 

UF rate is out of range. 

Dialog 

Message 

Enter a new UF Goal or reduce UF rate. 

Select Program 

This message is a prompt for the 
operator to select a program. 

Advisory 

To proceed, select the desired program and press 

CONFIRM

. 

Set Arterial Limits 

This is a message to re-center the 
arterial limits if necessary 

Advisory 

Press and hold 

Reset 

for 1 second to re-center the limits. 

Set Blood Flow to 300 

This message is a prompt for the 
operator to set the blood flow rate in 
preparation for the Access Flow test 

Warning 

To proceed, set 

Blood Flow

 to 300 and press 

CONFIRM

. 

Set TMP Limits? 

This is a message to re-center the 
TMP limits if necessary 

Advisory 

Rising TMP may indicate a leak in the balancing system and should 
be investigated. 

Press and hold 

Override 

for 1 second to re-center the limits. 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды