Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 200

Страница: 200 / 240

Appendix A—Single Needle Dialysis (Optional)

200

2008K Hemodialysis Machine Operator’s Manual Rev P

While keeping firm tension outward on the left (incoming) side of the bloodline,
press and hold the

Start/Stop

key a second time and the pump segment will be

released from the pump head.

Replace saline bag with a fresh bag if necessary

Rinse the blood in the bloodline back to the patient:

Clamp the arterial bloodline directly below the saline “T”

Open the saline line clamps

Start the blood pump and set a rate of 150-200 ml/min

When the blood has been returned to the patient, turn the blood pump off and close
the saline line clamps

Rinse the remaining blood in the arterial bloodline back to the patient:

Remove the clamp from below the saline “T” and then clamp the arterial bloodline
directly above the saline “T”

Open the saline line clamps

When the blood has been returned to the patient, close the saline line clamps

Warning!

Check all bloodlines and dialysate lines for leaks. Keep access sites uncovered

and monitored. Improper bloodline connections or needle dislodgements can result in
excessive blood loss, serious injury, and death. Machine alarms may not occur in every
blood loss situation.

Clamp the arterial and venous bloodlines and the patient’s arterial and venous access
lines, and aseptically disconnect them.

Note

Depending on how your machine was configured, and audible alarm may sound

when the saline solution reaches the optical sensor. Press

RESET

to silence the alarm.

Continue with the instructions listed in the “Removing the Dialyzer” section on page 122.

Содержание DIASAFE 2008 K

















































































































































































































































Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды