manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 114

Chapter 4—Monitoring the Treatment 

114 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Table 28 – The BVM Screen Features 

Feature 

Function 

 

The 

Relative Blood Volume

 (RBV) is the relation of the 

current blood volume and the blood volume on the start of 
dialysis expressed in %. Thus, RBV is always 100% in the 
beginning. If at the end of the dialysis, RBV is e.g. 80%, the 
blood volume has been reduced by 20%. There can also be 
values of above 100%. 

 

 

 

 

The 

Trend Indicator 

is an arrow, which roughly shows the 

current direction and intensity of blood volume change. On 
the display the arrow is shown to the right of the measured 
value for RBV. The arrow symbols have the following 
meanings: 

 

:  

significant increase  

 

 

 

 

:  

moderate increase 

 

 

 

:  

nearly constant 

 

 

 

:  

moderate decrease 

 

 

 

:  

significant decrease 

 

 

The red blood cells (erythrocytes) are responsible for the 
transport of gases in the blood (oxygen and carbon dioxide). 
Hemoglobin, an iron compound giving the erythrocytes their 
red color, is the active component in this process. 
The hematocrit (HCT) is the packed cell volume (almost 
exclusively of erythrocytes) in the blood volume. 

 

 

 

This button allows to set a patient individual Alert Level for 
RBV. The range is 70% to 100%. Entering zero deactivates 
the alert function. 
If RBV reaches the Alert Level, the machine will give an 
audible warning and will stop ultrafiltration.  Press 

RESET

 to 

turn the Ultrafiltration pump back on.  This alarm occurs only 
once if the user does not set another Alert Level. 

 

 

This graph shows the Relative Blood Volume 
in red.  During time periods when the BVM 
can’t determine RBV (e.g. saline flush) the red 
line will continue dotted with the last 
transferred value.  The yellow dotted line 
shows the alert level.  The vertical dotted line 
indicates the scheduled end of treatment. 

 

100

90

80

RBV

%

100

90

80

RBV

%

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды