Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 171

Страница: 171 / 240

Chapter 6—Alarms and Troubleshooting

171

2008K Hemodialysis Machine Operator’s Manual Rev P

Message

Purpose of Message

Type

Action Required

Minor Blood Leak?

A minor blood leak (approximately
0.35 – 0.45 ml/min) was detected in
the dialysate. Air can cause a false
alarm.

Warning

Press

RESET

to reset the alarm. Press

Override

to continue to run

the blood pump if the alarm cannot be reset.

Check dialysate fluid from the red dialyzer return line for presence of
blood with a blood leak test strip.

If test is negative, recheck with a new blood leak test strip. If
negative after three checks, follow steps below:

Press

Override

to continue to run the blood pump while

troubleshooting the alarm.

Check the dialyzer supply and dialyzer return lines for air leaks,
especially at the connectors and the filter in the dialyzer return line.

Press

RESET

to reset alarm.

If unable to reset the alarm, return the patient’s blood according to
procedure below (test positive) and alert a qualified service
technician.

If test is positive, proceed according to the unit’s blood-leak policy. If
facility policy is to return patient’s blood, follow the steps below.

Press

RESET

to reset all other blood flow alarms.

Press

Override

to enable the blood pump to run and return patient’s

blood per unit protocol.

Warning

: During an

override, the machine’s
blood leak detector is
inactive. You must
manually monitor the
treatment for evidence of
blood leak.

Note

: Override will activate the blood pump for about

three minutes while a blood leak alarm exists. Press

Override

again if needed.

Must Be Alarm Free

A conductivity alarm exists when an
SVS program attempted to start

Advisory

Correct the conductivity alarm and start the SVS program.

Must Calibrate to Run

Electronic self-test failure.

Alarm

Turn machine power off and back on. If alarm is not cleared, take the
machine out of service and alert a qualified technician.

Must Clear UF Removed

An action has been initiated that
requires the UF Removed to be
cleared to zero.

Warning

To proceed with the selected operation, set the UF Removed
treatment button to zero.

Содержание DIASAFE 2008 K

















































































































































































































































Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды