Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 79

Страница: 79 / 240

Chapter 3—Setting Treatment Parameters

2008K Hemodialysis Machine Operator’s Manual Rev P

To set the 2008K hemodialysis machine for sequential
dialysis:

Figure 37 – Setting Sequential Dialysis

After 60 minutes of pure ultrafiltration, an alarm sounds and the warning message, “

MINUTES FLOW OFF

,” appears in the Status Box. The operator has the option of

continuing pure ultrafiltration or starting dialysis. This alarm occurs only once.

To continue pure ultrafiltration,

press the

RESET

key on the left side of the control panel.

This will silence the alarm and terminate the warning message

To start the treatment

, touch the

Dialysate Flow

button in the “Home” screen, set it to the

prescribed rate using the data entry keypad, press

CONFIRM

, and start the dialysate flow by

pressing the

Dialysate Flow on/off

key in the upper, right corner of the control panel. When

dialysate flow is on, the yellow light is not illuminated.

3) Touch

Dialysate

Flow

to highlight it.

5) Press

CONFIRM

This

will deactivate the “Flow
Off” warning for five
minutes. The Dialysate
Flow button will display
“SEQ”.

1) Set UF treatment
parameters. Set the UF
Time to include the
combined treatment and
pure UF times.

4) Use the
number or arrow
keys to enter 0.

2) Turn off Dialysate
Flow. Yellow light
will flash when flow
is off.

Содержание DIASAFE 2008 K

















































































































































































































































Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды