manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 87

Chapter 3—Setting Treatment Parameters 

2008K Hemodialysis Machine Operator’s Manual Rev P 

87 

5.

 

Touch the 

Load Syringe

 button, then press the 

CONFIRM 

key.  The heparin pump 

carriage fully retracts.   

 

 

Warning! 

Make sure that there is sufficient heparin for the bolus and subsequent heparin 

infusion.  Do not load the syringe beyond the prescribed amount. 

6.

 

Pull back one of the barrel lock tabs and press the barrel of the syringe into place.  Slide 
the barrel wings of the syringe into the wings slot on the pump module.  With the barrel 
in place, release the barrel lock tab (see Figure 42). 

7.

 

Squeeze the carriage latch to open the plunger holder and allow the carriage assembly to 
move freely.  To prevent backup of blood into the syringe, be sure to slide the carriage 
upward until it is firmly seated against the syringe plunger 

8.

 

Release the carriage latch and allow the plunger lock tabs to clamp the plunger in place 
securely. 

 

Figure 42 – The 2008K Heparin Pump Module with Syringe Loaded and Connected 

Carriage 
Latch 

Slide 
Carriage 

Syringe 

Barrel 
Lock 
Tabs 

Wings 
Slot 

Syringe 
Plunger 

Plunger 
Lock Tabs 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды