manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 121

Chapter 4—Monitoring the Treatment 

2008K Hemodialysis Machine Operator’s Manual Rev P 

121 

Completion of Dialysis 

At the end of treatment, when the RTD timer has counted down to 0:00, an alarm sounds and 
the message, 

RTD = ZERO

, appears in the Status box.  An alarm also sounds when the set 

amount of ultrafiltrate has been removed.  When that happens, the Status Box displays the 
message, 

UF GOAL REACHED.

  To reset either alarm, press the

 RESET 

key.  If the 

UF 

GOAL REACHED

 and 

RTD = ZERO

 alarms occur simultaneously, pressing the

 RESET 

key 

will reset both alarms. 

Returning Blood to the Patient  

To return the blood to the patient: 

1.

 

Touch the 

Tx

 

Clock

 and then press 

CONFIRM

 to stop the treatment 

2.

 

Press the 

Start/Stop 

key on the blood pump to stop the pump  

3.

 

Replace saline bag with a fresh bag if necessary. 

4.

 

Rinse the blood in the patient end of the arterial bloodline back to the patient: 

a.

 

Using a hemostat, clamp the arterial bloodline directly above the saline “T”. 

b.

 

Open the saline line clamps and rinse the blood in the tubing below the saline “T” 
back to the patient.  When the blood in the line has been rinsed back to the patient, 
close the saline line clamps. 

5.

 

Rinse the remaining blood in the bloodline back to the patient: 

a.

 

Clamp the arterial bloodline directly under the saline “T”. 

b.

 

Remove the clamp on the bloodline above the saline “T” and open the saline line 
clamps. 

c.

 

Start the blood pump and set a rate of 150-200 ml/min. 

d.

 

When the blood has been returned to the patient, turn the blood pump off and close 
the saline line clamps. 

 

 

Warning!

 Check all bloodlines and dialysate lines for leaks.  Keep access sites uncovered 

and monitored.  Improper bloodline connections or needle dislodgements can result in 
excessive blood loss, serious injury, and death.  Machine alarms may not occur in every 
blood loss situation 

 

6.

 

Clamp the arterial and venous bloodlines and the patient’s arterial and venous access 
lines, and aseptically disconnect them.   

 

Note

:

 

Depending on how your machine was configured, and audible alarm may sound 

when the saline solution reaches the optical sensor.  Press 

RESET

 to silence the alarm.  

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды