manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 50

Chapter 2—Daily Preparation for Treatment 

50 

2008K Hemodialysis Machine Operator’s Manual Rev P 

11.

 

Press the 

RESET

 key on the control panel to restart the blood pump and continue 

flushing saline through the blood circuit in accordance with established facility protocol 
regarding dialyzer rinsing. 

12.

 

After the required saline amount has passed through the dialyzer, press the 

Start/Stop 

key on the blood pump to stop the pump. 

13.

 

Clamp the patient end of the venous bloodline.   

14.

 

Adjust the fluid levels in the drip chambers by pressing the appropriate 

 

or 

 level 

adjust keys.  Close the venous pressure monitor line clamp and disconnect the monitor 
line from the venous pressure port so the port is open to atmosphere. 

15.

 

Aseptically connect the patient end of the arterial bloodline to the patient end of the 
venous bloodline using a sterile recirculation piece.  Unclamp both lines. 

16.

 

Set the blood pump rate to 350-400 ml/min.  Press the blood pump 

Start/Stop 

key to 

start the pump and begin recirculation.  If necessary, press the 

RESET 

key to clear any 

alarms.  

17.

 

Ensure that the extracorporeal circuit is free of air bubbles 

 

 

Note

: The dialysate lines will have to be attached at the appropriate point during the 

priming process, depending on facility procedure and manufacturer’s instructions.  If 1.5x 
or 2x dialysate flow (Auto Flow) is selected, be sure that the dialysate flow rate is at least 
the minimum required rate. 

Prime Amount Method 

1.

 

Connect the dialyzer end of the arterial bloodline to the arterial port of the dialyzer. 
Rotate the dialyzer to the arterial end down position. 

2.

 

Connect the dialyzer end of the venous bloodline to the venous port of the dialyzer. 

3.

 

Hang a saline bag and attach an administration line, if not already attached, to the saline 
port on the arterial bloodline.  Aseptically spike the saline bag. 

4.

 

Gravity prime the patient end of the arterial bloodline below the saline “T” with saline.  
When primed, clamp off the patient end of the arterial bloodline.   

5.

 

If the heparin pump is to be used: connect the heparin syringe, prime the heparin line 
with heparin, and load heparin syringe into heparin pump.  If the heparin pump is not 
used, clamp the heparin line. 

6.

 

On the control panel, press the 

Prime 

key.   

7.

 

Press the blood pump 

Start/Stop 

key and run the blood pump at a rate of about 150-200 

ml/min.  Adjust the flow rate by pressing the 

 

(up) or 

 

(down) keys.  

8.

 

Fill the arterial drip chamber to an acceptable level using the 

 

or 

 

key (level adjust) 

key on the blood pump. Close the arterial pressure monitor line clamp and disconnect the 
line from the arterial pressure port so the port is open to atmosphere. 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды