manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 155

Chapter 6—Alarms and Troubleshooting 

155 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Message 

Purpose of Message 

Type 

Action Required

 

BPM: Pulse Amp Unif 

The amplitude of the pressure pulses 
is inconsistent with an accurate blood 
pressure profile.  

Blood 

Pressure 

Alarm 

Check pressure cuff for proper fit and alignment. Observe the patient 
for physiologic changes. Treat as patient as symptoms warrant. 

BPM: Pulse High 

The latest pulse reading is above the 
Upper Pulse alarm limit. 

Blood 

Pressure 

Alarm 

Observe the patient for physiologic changes.  Treat patient as 
symptoms warrant. 

BPM: Pulse Low 

The latest pulse reading is below the 
Lower Pulse alarm limit. 

Blood 

Pressure 

Alarm 

Observe the patient for physiologic changes.  Treat patient as 
symptoms warrant. 

BPM: Pump On > 30 sec 

The pump that inflates the cuff has 
been running longer than 30 seconds 
for an adult patient or longer than 10 
seconds for pediatric patient. 

Blood 

Pressure 

Alarm 

Cuff is not inflating.  Check for loose tubing connections or a leak in 
the cuff. 

 

 

BPM: Systolic High 

The systolic blood pressure reading is 
above the set Upper Systolic alarm 
limit. 

Blood 

Pressure 

Alarm 

Observe the patient for physiologic changes.  Treat patient as 
symptoms warrant. 

BPM: Systolic Low 

The systolic blood pressure reading is 
below the set Lower Systolic alarm 
limit. 

Blood 

Pressure 

Alarm 

Observe the patient for physiologic changes. Treat patient as 
symptoms warrant. 

BPM: Weak Pulse 

The pulse pressure is too weak to 
register an accurate measurement. 

Blood 

Pressure 

Alarm 

Check the cuff for proper fit and inflation. Observe the patient for 
physiologic changes. Treat patient as symptoms warrant. 

BPM: Zero Pressure 

No pressure is detected by the blood 
pressure module. 

Blood 

Pressure 

Alarm 

Check for a loose connection in the inflation system.  Correct as 
necessary.  If no leak found, turn the power off, then back on.  If 
problem persists, alert a qualified service technician. 

BTM test underway 

The OLC test may not be started 
when a BTM recirculation test is 
underway.  

Advisory 

Wait for the BTM recirculation test to complete before beginning the 
OLC test. 

BVM Failed 

The BVM module has failed 

Alarm 

Press 

RESET

 to clear the message.  BVM will no longer pass 

information to the 2008K monitor.  Turn the power off and back on.  If 
the alarm is not cleared, refer to a qualified service technician. 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды