manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 138

Chapter 6—Alarms and Troubleshooting 

138 

2008K Hemodialysis Machine Operator’s Manual Rev P 

 

Figure 63- Status Box and Dialogue Box during an Alarm Event 

The Dialogue Box, found in the upper right corner of the display screens, can provide 
information on the patient, prompt an action, or serve as a reminder.  The Dialogue Box can 
appear alone or supplement the message displayed in the Status Box during a Warning 
condition.  In some cases, Dialogue Boxes, if ignored for a prolonged period, can trigger a 
Warning message in the Status Box.  Although a Dialogue Box can appear during a Warning 
or Alarm event, the messages displayed in each may represent two separate, unrelated issues.   

Normal Status 

The Status Box displays a green background under normal operation when no problems have 
been detected.  During dialysis operation, the Status box will display a message describing 
the current mode of the machine—DIALYSIS.  When a Dialogue Box message is not 
displayed, the Dialogue Box displays the current time, patient blood pressure and pulse and 
the time taken.    

Warning Status 

The Status Box background changes to yellow when a Warning condition exists.  A Warning 
condition, although potentially serious, does not pose an immediate threat to the patient.  
Warning events do not stop the blood pump.  The message displayed in the Status Box is 
intended to alert the operator of a functional anomaly, a procedural error, or an existing 
condition requiring remedial action.  A warning may be accompanied by an audible alarm.   

Status Box 

Red for Alarms 

Yellow for Warnings 

Green under normal 
operating conditions

 

Dialogue Box

 

May provide additional 

information, reminders, or 

prompts for action

 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды