Xerox ColorQube 9303 Series, Service Manual

Page: 1423 / 1812

February 2013
6-131 ColorQube® 9303 Family
dC131
General Procedures/Information
801-014 Scan LE Hotline Scan LE hot line 0.1 mm increments
Range = 100 to 900 280
801-015 Mono Set Point Mono set point Grey Level in whole number
Range = 170 to 255 198
801-016 Red Set Point Red set point Grey Level in whole number
Range = 170 to 255 191
801-017 Green Set Point Green set point Grey Level in whole number
Range = 170 to 255 197
801-018 Blue Set Point Blue set point Grey Level in whole number
Range = 170 to 255 205
801-019 ReCalMag200 ReCalMag200 0 = Never
1 = Re-calibrate for non-
mixed originals
2 = Always Calibrate
Range = 0 to 2 1
801-020 CvtMonoAgcAd-
just CvtMonoAgcAdjus % whole numbers. 100 cor-
responds to no DADH offset
compensation. Setting
greater than 100 compen-
sates for DADH darker than
platen.
Range = 80 to 120 103
801-021 CvtRedAgcAdjust CvtRedAgcAdjus % whole numbers. 100 cor-
responds to no DADH offset
compensation. Setting
greater than 100 compen-
sates for DADH darker than
platen.
Range = 80 to 120 104
801-022 CvtGrnAgcAdjust CvtGrnAgcAdjus % whole numbers. 100 cor-
responds to no DADH offset
compensation. Setting
greater than 100 compen-
sates for DADH darker than
platen.
Range = 80 to 120 104
801-023 CvtBlueAgcAdjust CvtBlueAgcAdjus Tenths of %. 1000 (100%)
corresponds to no DADH
offset compensation. Setting
greater than 1000 compen-
sate for DADH darker than
platen.
Range = 80 to 120 103
Table 2 IIT DADH NVM ID 800-xxx
NVM ID NVM Name NVM Description Settings
Default
801-024 Speed Mode Speed mode 0 = 257 mm/s
1 = 234 mm/s
2 = 234 mm/s
Range = 0 to 3 0
801-025 Scanner Type Scanner type, full width
array or charged cou-
pled device 1 = FWA
2 = CCDS
Range = 0 to 255 1
801-026 IQ Parameter
Version IQ parameter version Holds the scan parameter
version index and distin-
guishes between minor vari-
ations within a scanner
family, e.g. filter change,
lens change. Set to 1 for
ColorQube at launch.
Range = 0 to 255 1
801-027 DADH / Platen
Configuration DADH / platen configu-
ration 0 = DADH / Platen present
1 = Platen only
Range = 0 to 1 1
Table 3 IOT NVM (IME) ID Range 400 to 439-xxx
NVM ID NVM Name NVM Description Settings Default
410-001 Transfix calibra-
tion front Transfix front load calibration
factor Range = -1,500 to
3,500 2,200
410-002 Transfix calibra-
tion rear Transfix rear load calibration
factor Range = -1,500 to
3,500 2,200
410-003 Transfix cal
invalid Invalidate transfix calibration Range = 0 to 1 1
410-004 Transfix Load for
Large Envelope Transfix load value for large
envelopes Range = 2,000 to
5,100 2,000
420-001 Ink Level Cyan Track ink mass - cyan (+) when sticks
added
(-) when pixels print
Range = 0 to
4,294,967,295 0
420-002 Ink Level
Magenta Track ink mass - magenta (+) when sticks
added
(-) when pixels print
Range = 0 to
4,294,967,295 0
420-003 Ink Level Yellow Track ink mass - yellow (+) when sticks
added
(-) when pixels print
Range = 0 to
4,294,967,295 0
Table 2 IIT DADH NVM ID 800-xxx
NVM ID NVM Name NVM Description Settings
Default