Xerox ColorQube 9303 Series, Service Manual

Page: 147 / 1812

February 2013
2-123 ColorQube® 9303 Family
12-181-00-171, 12-182-00-171
Status Indicator RAPs
Enter dC330 code 12-213. Actuate the BM exit sensor, Q12-213, Figure 2 . The display
changes.
Y
N
Go to
WD 12.18 . Check Q12-213.
Refer to:
• GP 11 How to Check a Sensor.
• 12A-171 HVF Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• BM PWB, PL 12.175 Item 10 .
• BM exit sensor, PL 12.185 Item 17 .
Enter dC330 , code 12-253 to run the BM crease roll motor, MOT12-253. The motor runs.
Y N
Go to
WD 12.18 . Check MOT12-253.
Refer to:
• GP 10 How to Check a Motor.
• 12A-171 HVF Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• BM crease roll motor, PL 12.175 Item 12 .
• BM PWB, PL 12.175 Item 10 .
Enter dC330 , code 12-253 to run the BM crease roll motor, MOT12-253. The motor drives
the gears.
Y
N
Install new components as necessary:
•
Crease roll drive train gears, PL 12.180 .
Enter dC330 , code 12-252 to run the BM crease blade motor, MOT12-252. The motor runs.
Y N
Go to
WD 12.18 . Check MOT12-252.
Refer to:
• GP 10 How to Check a Motor.
• 12A-171 HVF Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• BM crease blade motor, PL 12.170 Item 3 .
• BM PWB, PL 12.175 Item 10
NOTE: The BM crease roll gate motor has two component control codes:
12-273 cycles the crease roll gate.
12-276 opens the crease roll gate.
Enter dC330 , code 12-273 to cycle the BM crease roll gate motor, MOT12-273. The motor
runs.
Y
N
Go to
WD 12.18 . Check MOT12-273.
Refer to:
• GP 10 How to Check a Motor.
• 12A-171 HVF Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• BM crease roll gate motor, PL 12.175 Item 8 .
• BM PWB, PL 12.175 Item 10 .
The BM module has a tri-folder module installed.
Y
N
The fault may be intermittent, check for damaged wiring or bad connectors,
REP 1.1 . If
necessary install a new BM PWB, PL 12.175 Item 10 .
Check the drive coupler, PL 12.205 Item 17 is engaged with the BM crease roll motor encoder
disc, PL 12.175 Item 13 . The coupler and encoder are correctly engaged.
Y N
Align the drive coupler, refer to
REP 12.68-171 Tri-folder Drive Install Kit.
Check the drive assembly for wear, damage, contamination and misalignment, PL 12.205 Item
12 . The condition of the drive assembly is good.
Y N
Install a new drive assembly,
PL 12.205 Item 12 .
Check the condition of the drive belt, PL 12.205 Item 11 . The drive belt is good.
Y N
Install a new tri-folder install kit,
PL 12.205 Item 14 .
The fault may be intermittent, check for damaged wiring or bad connectors, REP 1.1 . If neces-
sary install a new BM PWB, PL 12.175 Item 10 .
A
B
B