Xerox ColorQube 9303 Series, Service Manual, Page: 510 / 1812

February 2013
2-486 ColorQube® 9303 Family
99-330-00 to 99-349-00
Status Indicator RAPs
99-330-00 to 99-349-00 PEST Error 11 RAP
99-330-00 Connector, IOD pre-amplifier PWB.
99-331-00 Connector DMU hot plug open.
99-332-00 Connector, registration / preheat interface PWB.
99-333-00 Connector, registration / preheat interface PWB.
99-334-00 Connector, registration / preheat interface PWB.
99-340-00 Connector, media path driver PWB.
99-341-00 Connector, media path driver PWB.
99-342-00 Connector, media path driver PWB.
99-343-00 Connector, media path driver PWB.
99-344-00 Connector, media path driver PWB.
99-345-00 Connector, media path driver PWB.
99-346-00 Connector, MPD harness M3
99-347-00 Connector, MPD harness M2
99-348-00 Connector, MPD harness M5
99-349-00 Connector, MPD harness M6
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
Procedure
Refer to Table 1 . Perform the relevant action. For an explanation of PEST codes refer to
dC123 .
Table 1 PEST Hard and Soft Fault Codes
Code Hard/Soft Action
99-330 Hard Check that PJ2 to the IOD pre-amp PWB, refer to WD 9.22 and WD
9.1 and PJ1 on the registration / pre-heat interface PWB, refer to WD
8.6 are securely connected. Check the wiring for an open circuit,
repair as necessary, REP 1.1 .
99-331 Hard This fault code is for future use and is included for reference only.
99-332 Hard Check that PJ4 on the registration / preheat interface is securely con-
nected. Check the wiring for an open circuit, repair as necessary,
REP 1.1 . Refer to WD 8.6 .
99-333 Hard Check that PJ5 on the registration / preheat interface is securely con-
nected. Check the wiring for an open circuit, repair as necessary,
REP 1.1 . Refer to WD 8.6 .
99-334 Hard Check that PJ1 on the registration / preheat interface is securely con-
nected. Check the wiring for an open circuit, repair as necessary,
REP 1.1 . Refer to WD 8.6 .
99-340 Hard Check that PJ202 on the media path driver PWB is securely con-
nected. Check the wiring for an open circuit, repair as necessary,
REP 1.1 . Refer to WD 8.1 .
99-341 Hard Check that PJ104 on the media path driver PWB is securely con-
nected. Check the wiring for an open circuit, repair as necessary,
REP 1.1 . Refer to WD 8.1 and WD 8.6 .
99-342 Hard Check that PJ303 on the media path driver PWB is securely con-
nected. Check the wiring for an open circuit, repair as necessary,
REP 1.1 . Refer to WD 8.1 and WD 8.5 .
99-343 Hard Check that PJ905 on the media path driver PWB is securely con-
nected. Check the wiring for an open circuit, repair as necessary,
REP 1.1 . Refer to WD 8.5 .
99-344 Hard Check that PJ406 on the media path driver PWB is securely con-
nected. Check the wiring for an open circuit, repair as necessary,
REP 1.1 . Refer to WD 8.4, WD 9.17 and WD 9.18 .
99-345 Hard Check that PJ405 on the media path driver PWB is securely con-
nected. Check the wiring for an open circuit, repair as necessary,
REP 1.1 . Refer to WD 8.3 .
99-346 Hard Check that PJ202 on the media path driver PWB harness to registra-
tion motor (M3) is securely connected. Check the wiring for an open
circuit, repair as necessary,
REP 1.1 . Refer to WD 8.1 .
99-347 Hard Check that PJ104 on the media path driver PWB harness to vertical
transport motor (M2) is securely connected. Check the wiring for an
open circuit, repair as necessary,
REP 1.1 . Refer to WD 8.1 .
99-348 Hard Check that PJ303 on the media path driver PWB harness to exit
motor (M5) is securely connected. Check the wiring for an open cir-
cuit, repair as necessary,
REP 1.1 . Refer to WD 8.2 .
99-349 Hard Check that PJ905 on the media path driver PWB harness to horizon-
tal transport motor (M6) is securely connected. Check the wiring for
an open circuit, repair as necessary,
REP 1.1 . Refer to WD 8.5 .
Table 1 PEST Hard and Soft Fault Codes
Code Hard/Soft Action