Xerox ColorQube 9303 Series, Service Manual

Page: 368 / 1812

February 2013
2-344 ColorQube® 9303 Family
83-120-00 to 83-125-00
Status Indicator RAPs
83-120-00 to 83-125-00 Media Path Sensor 17 RAP
83-120-00 Detected a sheet length too long over media path sensor 17.
83-121-00 Detected a sheet length too short over media path sensor 17.
83-122-00 Lead edge of sheet to late at media path sensor 17.
83-123-00 The trailing edge was late to clear media path sensor 17.
83-124-00 Trail edge of sheet failed to clear media path sensor 17 in time when inverting to
output
83-125-00 Lead edge of sheet arrives too early at media path sensor 17.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check for obstructions in the paper path.
• Check the vertical and horizontal transport rolls.
• If tabbed sheets are used, inform the customer to ensure that the sheets are fed with tab
trailing.
• If pre-drilled paper is used, check that the pre-drilled pages are fed with the holes trailing.
Procedure
Enter dC330 code 83-010 duplex sensor (17), Q83-010. Press Start. Open the front door and
manually actuate the sensor. The display changes.
Y
N
Go to
WD 8.5 . Check duplex sensor (17), Q83-010. Refer to:
• GP 11 How to Check a Sensor.
• PJ905, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Duplex sensor 17, PL 82.15 Item 3 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 82-003 Horizontal transport motor (M6), MOT82-003. Press Start. Then
enter the code 82-004 to run the motor in reverse. The motor runs in both forward and
reverse directions.
Y
N
Go to
WD 8.5 . Check Horizontal transport motor (M6), MOT82-003. Refer to:
• GP 10 How to Check a Motor.
• PJ905, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Horizontal transport motor (M6), PL 82.15 Item 9 .
• Media path driver PWB, PL 1.15 Item 5 .
The horizontal transport rolls rotate.
Y
N
Check the drive belts and drive gears on the horizontal transport,
PL 82.15 .
If necessary, install new components:
• Transport rolls, PL 82.15 Item 10 .
• Drive belts, PL 82.15 Item 7 and PL 82.15 Item 8 .
• Drive gears, PL 82.15 Item 6 , PL 82.15 Item 13 and PL 82.15 Item 16 .
Enter dC140 Analog Monitor. Select 82-102 horizontal transport motor encoder (M6). Press
Start. The number of ticks (i.e. 36 ticks) will flash on the display and then return to show 0 ticks.
Repeat by selecting stop and then start on the popup menu, the number only remains for a few
seconds. The number of ticks is displayed.
Y
N
Go to
WD 8.5 . Check horizontal transport motor (M6), MOT82-003. Refer to:
• GP 10 How to Check a Motor.
• PJ905, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Horizontal transport motor (M6), PL 82.15 Item 9 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 83-004 HPP diverter solenoid, SOL 83-004, press start. Ensure that the
HPP diverter gate moves fully when the solenoid is energized and returns fully when the sole-
noid is generalized. The solenoid energizes and the diverter gate moves correctly.
Y
N
Go to
WD 8.1 , check SOL 83004. Refer to:
• GP 12 How to Check a Solenoid or Clutch
• PJ303 Media Path Driver PWB .
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• HPP diverter solenoid, PL 82.15 Item 5 .
• Horizontal paper path assembly, PL 82.15 Item 1 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 82-008 nip D release solenoid, SOL 82-008, press start. The solenoid
energizes.
Y
N
Go to
WD 8.3 , check SOL 82-008, refer to:
• GP 12 How to Check a Solenoid or Clutch.
A
A
B