Xerox ColorQube 9303 Series, Service Manual, Page: 358 / 1812

February 2013
2-334 ColorQube® 9303 Family
82-145-00, 82-146-00, 82-150-00, 82-151-00, 82-156-00
Status Indicator RAPs
82-145-00, 82-146-00, 82-150-00, 82-151-00, 82-156-00
Media Path Sensor 14 Time Out in Duplex Mode RAP
82-145-00 The sheet was too long to clear sensor 14 in duplex mode.
82-146-00 The sheet was too short to clear the media path sensor 14 in duplex mode.
82-150-00 Lead edge late too the media path sensor 14 in duplex mode.
82-151-00 Trail edge late too clear the media path sensor 14 in duplex mode.
82-156-00 Lead edge of sheet too early at the media path sensor 14 in duplex mode.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check for obstructions in the paper path.
• Check the vertical and horizontal transport rolls for contamination or wear.
Procedure
Enter dC330 code 83-125 duplex end sensor (14), Q83-125. Press Start. Open the front door
and manually actuate the sensor. The display changes.
Y
N
Go to
WD 8.5 . Check duplex end sensor (14), Q83-125. Refer to:
• GP 11 How to Check a Sensor.
• PJ905, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Duplex end sensor 14, PL 82.15 Item 3 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 82-001 vertical transport motor (M2), MOT82-001. Press Start. The motor
runs.
Y
N
Go to
WD 8.1 . Check vertical transport motor (M2), MOT82-001. Refer to:
• GP 10 How to Check a Motor.
• PJ104, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Vertical Transport motor (M2), PL 82.10 Item 12 .
• Media path driver PWB, PL 1.15 Item 5 .
The vertical transport rolls rotate.
Y
N
Check the drive belt and drive gears on the vertical transport,
PL 82.10 .
If necessary, install new components:
• Transport rolls, PL 82.10 Item 1 , PL 82.10 Item 2 .
• Drive belts, PL 82.10 .
• Drive gears, PL 82.10 .
Enter dC140 Analog Monitor. Select 82-100 vertical transport motor encoder (M2). Press Start.
The number of ticks (i.e. 36 ticks) will flash on the display and then return to show 0 ticks.
Repeat by selecting stop and then start on the popup menu, the number only remains for a few
seconds. The number of ticks is displayed.
Y
N
Go to
WD 8.1 . Check vertical transport motor (M2), MOT82-001 and the encoder wire
harness. Refer to:
• GP 10 How to Check a Motor.
• PJ104, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Vertical transport motor (M2), PL 82.10 Item 12 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 82-008 nip D release solenoid, SOL82-008. Press Start. The solenoid
energize.
Y
N
Go to
WD 8.3 . Check nip D release solenoid, SOL82-008. Refer to:
• GP 12 How to Check a Solenoid or Clutch.
• PJ405, Media path driver PWB .
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Nip D release solenoid, PL 70.30 Item 13 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 82-007 Nip C release solenoid, SOL82-007. Press Start. The solenoid
energizes.
Y
N
Go to
WD 8.1 . Check SOL82-007. Refer to:
• GP 12 How to Check a Solenoid or Clutch.
• PJ303, Media path driver PWB .
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Nip C release solenoid, PL 82.15 Item 4 .
• Media path driver PWB, PL 1.15 Item 5 .
A
A
B