Xerox ColorQube 9303 Series, Service Manual, Page: 105 / 1812

February 2013
2-81 ColorQube® 9303 Family
12-024-00-110, 12-025-00-110
Status Indicator RAPs
12-024-00-110, 12-025-00-110 Paddle Roll Failure RAP
12-024-00-110 The paddle is not at the home position.
12-025-00-110 The paddle fails to rotate.
NOTE: The paddle is in the home position when the sensor flag is located between the sensor
jaws. If a jam occurs in the compiler, bin 1 will not be available.
NOTE: With reference to WD 12.3 component control codes;
Code 12-237 drives the paddle roll motor until the paddle wheel shaft assembly is at the home
position.
Code 12-238 runs the paddle roll motor.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
WARNING
Take care not to topple the LCSS. The LCSS is unstable when undocked from the
machine. Do not show the customer how to undock the LCSS.
Check the following:
• That there is no paper or other obstructions in the vicinity of the paddle.
• The paddle roll position sensor bracket is holding the sensor in the correct position, i.e.
the flag is in the middle of the sensor gap and the sensor does not touch any moving com-
ponents.
• Check that the paper type is set correctly. If heavyweight paper is used but not set in the
UI, the compiler capacity can be exceeded. Refer to
12J-110 Mis-Registration in Stapled
Sets and Non-stapled Sets RAP.
• Check the position of the paddles. With the paddle roll in the home position both sets of
paddles must be within the output cover, if they are not, refer to
REP 12.12-110 Paddle
Wheel Shaft Assembly. If any of the paddles are out of alignment to other paddles, install
a new paddle wheel shaft assembly,
PL 12.25 Item 4 or a new paddle, PL 31.10 Item 4 .
• LCSS PWB DIP switch settings, refer to 12F-110 LCSS PWB DIP Switch Settings RAP.
Procedure
NOTE: All LCSS interlocks must be made to 24V to the motors.
NOTE: In diagnostics, actuating any LCSS sensor or switch can change the displayed state on
the UI. Make sure that the correct sensor or switch is tested.
Run the paddle roll motor MOT 12-238, PL 12.25 Item 10 . Enter dC330 codes 12-237 paddle
roll motor home position and 12-238 paddle roll motor run. The paddle rotates correctly.
Y
N
Go to
WD 12.3 . Check the paddle roll motor MOT12-238.
Refer to:
• 12G-110 LCSS PWB Damage RAP.
• GP 10 , How to Check a Motor.
• P/J310, LCSS PWB.
• 12D-110 LCSS Power Distribution RAP
• 01L 0V Distribution RAP
Install new components as necessary:
• Paddle roll motor, PL 12.25 Item 10 .
• LCSS PWB, PL 12.75 Item 1 .
Enter dC330 code 12-238 and stack the code 12-186, to actuate the paddle roll motor home
sensor Q12-186. The display cycles high/low.
Y
N
Go to
WD 12.4 . Check Q12-186.
Refer to:
• 12G-110 LCSS PWB Damage RAP.
• GP 11 , How to Check a Sensor.
• P/J314, LCSS PWB.
• 12D-110 LCSS Power Distribution RAP
• 01L 0V Distribution RAP
Install new components as necessary:
• Paddle roll motor home sensor, PL 12.25 Item 11 .
• LCSS PWB, PL 12.75 Item 1 .
Perform SCP 5 Final Actions.
A
A