Xerox ColorQube 9303 Series, Service Manual, Page: 353 / 1812

February 2013
2-329 ColorQube® 9303 Family
82-132-00, 82-155-00
Status Indicator RAPs
82-132-00, 82-155-00 Media Path Sensor 16 Duplex Mode
RAP
82-132-00 Lead edge timed out, sheet late at the media path sensor 16 in duplex mode.
82-155-00 Lead edge too early at the media path sensor 16 in duplex mode.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check for obstructions in the paper path.
• Check the vertical and horizontal transport rolls for contamination or wear.
• Check that the upper and middle left side doors are fully latched.
Procedure
Enter dC330 code 82-125 confirm sensor (16), Q82-125. Press Start. Open the left hand door
and manually actuate the sensor. The display changes.
Y
N
Go to
WD 8.1 . Check confirm sensor (16), Q82-125. Refer to:
• GP 11 How to Check a Sensor.
• PJ104, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Confirm sensor 16, PL 82.10 Item 7 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 82-002 vertical transport motor (M2) (reverse), MOT82-001. Press Start.
The motor runs.
Y
N
Go to
WD 8.1 . Check vertical transport motor (M2), MOT82-001. Refer to:
• GP 10 How to Check a Motor.
• PJ104, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Vertical Transport motor 2, PL 82.10 Item 12 .
• Media path driver PWB, PL 1.15 Item 5 .
The vertical transport rolls rotate.
Y
N
Check the drive belt and drive gears on the vertical transport,
PL 82.10 .
If necessary, install new components:
• Transport rolls, PL 82.10 .
• Drive belts, PL 82.10 .
• Drive gears, PL 82.10 .
Enter dC140 Analog Monitor. Select 82-100 vertical transport motor encoder (M2). Press Start.
The number of ticks (i.e. 36 ticks) will flash on the display and then return to show 0 ticks.
Repeat by selecting stop and then start on the popup menu, the number only remains for a few
seconds. The number of ticks is displayed.
Y
N
Go to
WD 8.1 . Check vertical transport motor (M2), MOT82-001and the encoder wire har-
ness. Refer to:
• GP 10 How to Check a Motor.
• PJ104, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Vertical transport motor (M2), PL 82.10 Item 12 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 82-004 Horizontal transport motor (M6) (reverse), MOT82-003. Press Start.
The motor runs.
Y
N
Go to
WD 8.5 . Check horizontal transport motor (M6), MOT82-003. Refer to:
• GP 10 How to Check a Motor.
• PJ905, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Horizontal transport motor (M6), PL 82.15 Item 9 .
• Media path driver PWB, PL 1.15 Item 5 .
The horizontal transport rolls rotate.
Y
N
Check the drive belt and drive gears on the horizontal transport,
PL 82.10 / PL 82.15 .
If necessary, install new components:
• Transport rolls, PL 82.15 .
• Drive belts, PL 82.15 .
• Drive gears, PL 82.15 .
Enter dC140 Analog Monitor. Select 82-102 horizontal transport motor encoder (M6). Press
Start. The number of ticks (i.e. 36 ticks) will flash on the display and then return to show 0 ticks.
Repeat by selecting stop and then start on the popup menu, the number only remains for a few
seconds. The number of ticks is displayed.
A
A