Veeco K465i GaN Operation And Maintenance Download | Manualshive

Page: 103 / 352

background image

K465i Operations and Maintenance

P/N 1212831 Rev C

Page 4-25

Copyright

©

2012

Veeco Instruments, Inc. Confidential

All Rights Reserved

Section 4.4.

Palladium Cell Operation

This section contains information on the operation of the Johnson Matthey HP-230 V-Purge
Palladium cell. Information in this section is a direct subset summary of the

Johnson

Matthey Manual

. Please refer to the

Johnson Matthey Manual

, supplied as part of the

Vendor

Documentation

list/appendix in this document and on the

Technical Documentation CD

, for

complete operating instructions.

Safety Precautions and Hazard Management



Hydrogen gas is flammable and can result in explosion.



The surface of the Palladium Cells can be extremely hot.



Use extreme caution when working on gas lines as they may be pressurized. Utilize

pressure gauges to assure that pressure is not present in the lines prior to
maintenance.



Refer to the MSDS for hydrogen for flammability and explosivity data.



Use extreme caution when handling the Palladium cells. Protective gloves may be
required if the cell is abnormally hot.

PROCEDURES IN THIS SECTION



Operating Precautions



Cell Installation



Cell Operation



Cell Removal

REFERENCE DRAWINGS

The followings drawings are provided to assist in the performance of the procedures
contained in this section.

Reference Drawings List

System Footprint

Generic System Diagram (GSD)

«
...
101
102
103
104
105
...
»

Summary of Contents for K465i GaN

































































































































































































































































































































































Reviews:

No comments

Related manuals for K465i GaN

Brand: ParaBody Pages: 4

Brand: Baileigh Industrial Pages: 40

Brand: Abus Pages: 2

Brand: Abus Pages: 12

Brand: Abu Garcia Pages: 6

Brand: Rangevision Pages: 28

Brand: Califone Pages: 7

Brand: CALITEK Pages: 16

Brand: LAHTI PRO Pages: 20

Brand: LAHTI PRO Pages: 16

Brand: J&M Pages: 53

Brand: Qazqa Pages: 2

Brand: Danelec Pages: 67

Brand: A&D Pages: 29

Brand: V-GREAT Pages: 4

Brand: Costan Pages: 154

Brand: Southern States Pages: 36

Brand: SOMFY Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands