manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 99

ENGINE

G23, G26, WSM

1-S17

(EU)

(2) Lubricating System

Engine Oil Pressure

1. Remove the engine oil pressure switch, and set an oil pressure

tester.

2. Start the engine. After warming up, measure the oil pressure of

both idling and rated speeds.

3. If the oil pressure is less than the allowable limit, check the

following.

• Engine oil insufficient
• Oil pump defective
• Oil strainer clogged
• Oil filter cartridge clogged
• Oil gallery clogged
• Excessive oil clearance
• Foreign matter in the relief valve

(When reassembling)

• After checking the engine oil pressure, tighten the engine oil

pressure switch to the specified torque.

9Y1210294ENS0007US0

Relief Valve

1. Remove the oil filter base.
2. Check the relief valve for dirt, and the seat and ball for damage.
3. If damaged, replace.
4. Check the free length of spring.
5. If less than the allowable limit, replace.

9Y1210294ENS0008US0

Engine oil pressure

Factory 
specifica-
tion

At idle 
speed

More than
49 kPa
0.50 kgf/cm

2

7.1 psi

At rated 
speed

197 to 441 kPa
2.00 to 4.50 kgf/cm

2

28.5 to 64.0 psi

Allowable 
limit

At rated 
speed

147 kPa
1.50 kgf/cm

2

21.3 psi

Tightening torque

Oil pressure switch

15 to 19 N·m
1.5 to 2.0 kgf·m
11 to 14 lbf·ft

Relief valve spring

Factory specification

32 mm
1.26 in.

Allowable limit

28 mm
1.10 in.

Tightening torque

Joint

40 to 49 N·m
4.0 to 5.0 kgf·m
29 to 36 lbf·ft

(1) Relief Valve
(2) Joint

(3) Spring

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands