manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 211

FRONT AXLE

G23, G26, WSM

3-S5

(EU)

[2] DISASSEMBLING AND ASSEMBLING

(1) Separating Front Axle Assembly

Dismounting Mower

1. Raise the mower deck to the top position. Disconnect the

universal joint (4).
For installation and uninstallation, set the anti-scalp rollers
(Front) as shown the figure below.
RCK48, RCK54 : Two places

2. Set the cutting height less than 88.9 mm (3.5 in.).

For installation and uninstallation, set the anti-scalp rollers
(Rear) as shown in the figure.
RCK48, RCK54 : Two places

3. Place the mower lift lever in the 

"DOWN"

 position.

(When mounting)

• Reverse the dismounting procedures.

9Y1210294FAS0006US0

(1) Anti-scalp Roller (Front)
(2) Anti-scalp Roller (Rear)

(3) Clevis Pin
(4) Universal Joint

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands