Kubota G23 Workshop Manual Download Page 174

Page: 174 / 343

TRANSAXLE

G23, G26, WSM

2-S13

(EU)

PTO Clutch Operating Pressure

CAUTION

• When checking, park the machine on flat ground, apply the

parking brake.

1. Lift the rear of the tractor and remove the left rear wheel.
2. Disconnect the PTO clutch delivery hose (2) from the PTO

clutch assembly (1), then install the adaptor, cable and pressure
gauge between the PTO clutch delivery hose (2) and the PTO
clutch assembly (1).

3. Start the engine and set at maximum speed.
4. Move the PTO lever to

"Engaged"

position, and measure the

pressure.

5. If the measurement is not same as factory specifications, check

the PTO relief valve and related hydraulic components.

IMPORTANT

• Do not connect the universal joint of the implement to the

mid and rear PTO shaft.

NOTE

• When reinstalling the PTO clutch delivery hose, connect

the PTO clutch delivery hose to the PTO clutch assembly
securely.

Condition

• Engine speed

Maximum

• Oil temperature

45 to 55 °C
113 to 131 °F

9Y1210294TXS0012US0

Adjusting Clearance between Tension PTO Arm and Release
Arm

1. Set the PTO lever (1) to

"DISENGAGED"

position

"B"

to make

the clutch wire (7) to be free.

2. Push the release arm (6) toward the tension PTO arm (2) to

contact. Tighten the bolt (5).

3. Check clearance between the tension PTO arm (2) and the

release arm (6).

4. If the measurement is not within the factory specifications,

adjust the clearance again.

9Y1210294TXS0048US0

PTO clutch operating
pressure

Factory specification

1.0 to 1.3 MPa
11 to 13 kgf/cm

150 to 180 psi

(1) PTO Clutch assembly
(2) PTO Clutch Delivery Hose
(3) PTO Lever (G26)

A : Engaged
B : Disengaged

Clearance between
tension PTO arm and
release arm

Factory specification

0 to 0.5 mm
0 to 0.02 in.

(1) PTO Lever
(2) Tension PTO Arm
(3) Clutch Wire
(4) Pulley (PTO Clutch Side)
(5) Bolt
(6) Release Arm
(7) Pulley

A : ENGAGED
B : DISENGAGED

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands

Kubota G23, Workshop Manual

Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands