Kubota G23 Workshop Manual Download Page 144

Page: 144 / 343

ENGINE

G23, G26, WSM

1-S62

(EU)

Oil Clearance between Crankshaft Journal and Crankshaft
Bearing 2 and Crankshaft Bearing 3 (G23)

1. Put a strip of plastigage on the center of the journal.
2. Install the bearing case and tighten the bearing case screws 1

to the specified torque, and remove the bearing case again.

3. Measure the amount of the flattening with the scale, and get the

oil clearance.

4. If the oil clearance exceeds the allowable limit, replace the

crankshaft bearing 2 (crankshaft bearing 3).

5. If the same size bearing is useless because of the crankshaft

journal wear, replace it with an undersize one referring to the
table and figure.

NOTE

• Be sure not to move the crankshaft while the bearing case

screws are tightened.

(Reference)

• Undersize crankshaft bearing 2 and 3 (0.20 mm (0.0079 in.))

• Undersize crankshaft bearing 2 and 3 (0.40 mm (0.016 in.))

• Undersize dimensions of crankshaft journal

9Y1210294ENS0082US0

Oil clearance between
crankshaft journal and
crankshaft bearing 2
(crankshaft bearing 3)

Factory specification

0.028 to 0.059 mm
0.0011 to 0.0023 in.

Allowable limit

0.20 mm
0.0079 in.

Crankshaft journal O.D.
(Flywheel side)

Factory specification

43.934 to 43.950 mm
1.7297 to 1.7303 in.

Crankshaft bearing 2 I.D.

Factory specification

43.978 to 43.993 mm
1.7315 to 1.7320 in.

Crankshaft journal O.D.
(Intermediate)

Factory specification

43.934 to 43.950 mm
1.7297 to 1.7303 in.

Crankshaft bearing 3 I.D.

Factory specification

43.978 to 43.993 mm
1.7315 to 1.7320 in.

Bearing

Code Number

Marking

Crankshaft bearing 2 02

1G460-23930

020 US

Crankshaft bearing 3 02

1G460-23940

Bearing

Code Number

Marking

Crankshaft bearing 2 04

1G460-23950

040 US

Crankshaft bearing 3 04

1G460-23960

Undersize

0.20 mm

0.0079 in.

0.40 mm
0.016 in.

Dimension

1.8 to 2.2 mm radius

0.071 to 0.086 in. radius

1.8 to 2.2 mm radius

0.071 to 0.086 in. radius

*Dimension

1.0 to 1.5 mm relief

0.040 to 0.059 in. relief

1.0 to 1.5 mm relief

0.040 to 0.059 in. relief

Dimension

43.734 to 43.750 mm dia.

1.7219 to 1.7224 in. dia.

43.534 to 43.550 mm dia.

1.7140 to 1.7145 in. dia.

Dimension

43.734 to 43.750 mm dia.

1.7219 to 1.7224 in. dia.

43.534 to 43.550 mm dia.

1.7140 to 1.7145 in. dia.

The crankshaft journal must be fine-finished to higher than Rmax=0.8S
*Holes to be de-burred and edges rounded with 1.0 to 1.5 mm (0.040 to
0.059 in.) relief.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands

Kubota G23, Workshop Manual

Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands