manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 100

ENGINE

G23, G26, WSM

1-S18

(EU)

(3) Cooling System

Fan Belt Tension

1. Measure the deflection 

(A)

, depressing the belt halfway

between the fan drive pulley and alternator pulley at specified
force 98 N (10 kgf, 22 lbf).

2. If the measurement is not within the factory specifications,

loosen the alternator mounting screws and relocate the
alternator to adjust.

9Y1210272ENS0017US0

Fan Belt Damage and Wear

1. Check the fan belt for damage.
2. If the fan belt is damaged, replace it.
3. Check if the fan belt is worn and sunk in the pulley groove.
4. If the fan belt is nearly worn out and deeply sunk in the pulley

groove, replace it.

9Y1210272ENS0018US0

 CAUTION

• When removing the radiator cap, wait at least ten minutes after the engine has stopped and cooled down.

Otherwise, hot water may gush out, scalding nearby people.

9Y1210294ENS0011US0

Radiator Cap Air Leakage

1. Set a radiator tester (1) and adaptor (2) on the radiator cap.
2. Apply the specified pressure 88 kPa (0.90 kgf/cm

2

, 13 psi), and

measure the time for the pressure to fall to 59 kPa (0.60 kgf/cm

2

,

8.6 psi).

3. If the measurement is less than the factory specifications,

replace the radiator cap.

9Y1210294ENS0009US0

Deflection 

(A)

Factory specification

7.0 to 9.0 mm
0.28 to 0.35 in.

(A) Deflection

(A) Good

(B) Bad

Pressure falling time

Factory specification

More than 10 seconds for 
pressure fall
88 

→

 59 kPa

(0.90 

→

 0.60 kgf/cm

2

,

13 

→

 8.6 psi)

(1) Radiator Tester

(2) Adaptor

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands