manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 69

GENERAL

G23, G26, WSM

G-51

(EU)

Checking and Replacing Blade

 CAUTION

To avoid personal injury :

• Be sure to stop the engine and remove the key.
• Blades may be sharp. When you handle blades, wear heavy

gloves or wrap end of blade with a rag.

Q

Checking

The blade cutting edges should be kept sharp at all times.

Sharpen the cutting edges, if they resemble blade 

(b)

. Replace the

blades if they appear similar to blade 

(c)

.

Q

Replacing 

1. Remove the mower deck from the machine.
2. Remove the two snap pins and the shaft, and then remove the

mower duct with sliding it.

NOTE

• When reinstalling the mower duct, make sure that the both

stays of the mower cover are set between the two washers.

3. Turn the mower deck over to expose the blades.
4. Wedge a block of wood between the blade and mower housing

as illustrated.

5. The blade bolts (5) have right hand threads, turn

counterclockwise to loosen.
The blade bolt (6) has left hand threads, turn clockwise to
loosen.

(To be continued)

(1) Mower Duct
(2) Snap Pin
(3) Shaft
(4) Block
(5) Blade Bolt
(6) Blade Bolt

(a) New Blade
(b) Worn Blade
(c) Cracked Blade
A : Slide
B : Loosen

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands