manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 276

ELECTRICAL SYSTEM

G23, G26, WSM

6-M9

(EU)

[3] FUEL LEVEL GAUGE

Fuel level gauge and fuel level sensor are connected

by the wiring.

Fuel level gauge detects the resistance from the fuel

lever sensor.

Fuel level gauge indicates the fuel level in the fuel

tank.

The relationship between the resistance of the fuel

level sensor and the fuel level gauges is as follows.

9Y1210294ELM0008US0

[4] WATER TEMPERATURE GAUGE

Water temperature gauge is located on the meter

panel board.

The water temperature gauge and the thermo unit

are connected by the wiring.

The water temperature gauge detects the resistance

from the thermo unit.

The water temperature gauge indicates the coolant

temperature in the engine cylinder head.

The relationship between the resistance of thermo

unit and reading on the water temperature gauge is as
follows.

9Y1210294ELM0009US0

Resistance of Fuel Level 

Sensor

Reading on Fuel Level Gauge

Approx. 110 

Ω

Empty

Approx. 3 

Ω

Full

(1) Fuel Level Gauge
(2) Fuel Level Sensor

A : Empty
B : Full

Resistance of Thermo Unit

Reading on Water 

Temperature Gauge

Approx. 220 

Ω

Min.

Approx. 70 

Ω

Start of Red

Approx. 3 

Ω

Max.

(1) Water Temperature Gauge
(2) Thermo Unit

A : Min.
B : Start of Red
C : Max.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands