manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 275

ELECTRICAL SYSTEM

G23, G26, WSM

6-M8

(EU)

5. GAUGES

[1] ELECTRICAL CIRCUIT

The fuel quantity is indicated by the fuel gauge. The coolant temperature is indicated by the water temperature

gauge.

9Y1210294ELM0006US0

[2] HOUR AND TACHOMETER

The electrical hour meter and tachometer is

equipped on the meter panel.

This meter indicates the operated hours when the

main switch is turned to 

"ON"

 position.

After starting the engine, this meter indicates the

present engine revolution.

The meter picks up the voltage from the IC regulator

located in the alternator.

The IC regulator sends a signal of the engine

revolution to the meter.

The meter calculates the signal. It changes and

indicates the signal to the engine revolution in
cooperation with the voltage.

9Y1210294ELM0007US0

(1) Hour and Tachometer
(2) Water Temperature Gauge
(3) Thermo Unit

(4) Fuel Gauge
(5) Fuel Sensor
(6) Frame Earth

(7) Alternator
(8) Slow Blow Fuse
(9) Fuse

(10) Main Switch
(11) Battery

(1) Electrical Hourmeter and 

Tachometer

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands