manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 318

MOWER

G23, G26, WSM

7-S5

(EU)

Mower Deck Left Side Height and Right Side Height
Adjustment

 CAUTION

To avoid personal injury :

• Shut off the engine and remove the key.
• Set the parking brake.
• Allow the blades to stop before making adjustments.
• Wear heavy gloves or wrap end of the blade with a rag when

you handle blades; Blades may be sharp.

1. Park the machine on a level surface.
2. Tyre inflation pressure must be correct.
3. Raise the mower lift lever to the top position.

Turn the cutting height control dial to adjust height to the desired
height.

4. Lower the mower deck by pushing the mower lift lever forward.
5. Turn the left blade so that it is parallel to rear axle.
6. Measure from outside blade tip (L) to the level surface.

Then turn the right blade so that it is parallel to rear axle.
Measure from outside blade tip (R) to the level surface.

7. Adjust the bolts with the lock nut on mower stay so that the

difference between measurements (L) and (R) is less than 
3 mm (0.12 in.).

9Y1210294MOS0006US0

[2] DISASSEMBLING AND ASSEMBLING

Drain Gear Box Oil

1. Tilt the mower deck.
2. Remove the drain plugs (2).
3. Drain the gear box oil from the gear case (4) and the blade

spindle cases (3).

(When reassembling)

9Y1210294MOS0007US0

Mower deck left side 
height and right side 
height difference

Factory specification

Less than
3 mm
0.12 in.

(1) Lock Nut
(2) Adjusting Bolt

A : Outside blade tip to the level 

surface

RCK48-G23

Oil capacity

1.9 L
2.0 U.S.qts
1.7 Imp.qts

RCK54-G26

2.1 L
2.2 U.S.qts
1.8 Imp.qts

(1) Oil Level Dipstick
(2) Drain Plug

(3) Spindle Case
(4) Gear Case

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands