manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 230

STEERING

G23, G26, WSM

4-S8

(EU)

[3] SERVICING

Steering Cylinder I.D.

1. Measure the steering cylinder I.D. with a cylinder gauge.
2. If the cylinder I.D. exceed the allowable limit, replace the

cylinder barrel.

9Y1210294STS0011US0

Clearance between Rod and Guide

1. Measure the rod guide I.D. with a cylinder gauge.
2. Measure the rod O.D. with an outside micrometer, and calculate

the clearance.

3. If the clearance exceeds the allowable limit, replace as a unit.

9Y1210294STS0012US0

Steering cylinder I.D.

Factory specification

40.000 to 40.062 mm
1.5787 to 1.5772 in.

Allowable limit

40.100 mm
1.5787 in.

Clearance between rod 
and guide

Factory specification

0.020 to 0.070 mm
0.00079 to 0.0027 in.

Allowable limit

0.200 mm
0.00787 in.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands