Kubota G23 Workshop Manual Download Page 203

Page: 203 / 343

TRANSAXLE

G23, G26, WSM

2-S42

(EU)

(5) Hydraulic PTO Clutch

Bearing

1. Hold the inner race, and push and pull the outer race in all

directions to check wear and roughness.

2. Apply the transmission oil to the bearing, and hold the inner

race. And turn the outer race to check rotation.

3. If there are any defect, replace the bearing

9Y1210294TXS0056US0

PTO Clutch Disk Plate Wear

1. Measure the thickness of PTO clutch disk with vernier calipers.
2. If the thickness is less than the allowable limit, replace it.

9Y1210294TXS0057US0

Separate Plate and Backing Plate Wear

1. Measure the thickness of the separate plate and the backing

plate with vernier calipers.

2. If the thickness is less than the allowable limit, replace it.

9Y1210294TXS0058US0

Flatness of Clutch Piston, Separate Plate and Backing Plate

1. Place the part on a surface plate.
2. Check the flatness by inserting a feeler gauge (allowable limit

size) underneath it at least four points.

3. If the gauge can be inserted, replace it.

9Y1210294TXS0059US0

Brake Spring Free Length

1. Measure the free length of brake spring with venire calipers.
2. If the measurement is less than the allowable limit, replace it.

9Y1210294TXS0060US0

Thickness of PTO clutch
disk

Factory specification

1.50 to 1.70 mm
0.0591 to 0.669 in.

Allowable limit

1.35 mm
0.0531 in.

Thickness of separate
plate

Factory specification

0.9450 to 1.055 mm
0.03721 to 0.04153 in.

Allowable limit

0.80 mm
0.031 in.

Thickness of backing
plate

Factory specification

1.9 to 2.1 mm
0.075 to 0.082 in.

Allowable limit

1.85 mm
0.0728 in.

Flatness of clutch piston

Allowable limit

0.15 mm
0.0059 in.

Flatness of separate
plate and backing plate

Allowable limit

0.20 mm
0.0079 in.

Brake spring free length

Factory specification

41.5 mm
1.63 in.

Allowable limit

37.5 mm
1.48 in.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands

Kubota G23, Workshop Manual

Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands