manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 143

ENGINE

G23, G26, WSM

1-S61

(EU)

Oil Clearance between Crankshaft Journal and Crankshaft
Bearing 1 (G26)

1. Measure the O.D. of the crankshaft front journal with an outside

micrometer.

2. Measure the I.D. of the crankshaft bearing 1 with an inside

micrometer, and calculate the oil clearance.

3. If the clearance exceeds the allowable limit, replace the

crankshaft bearing 1.

4. If the same size bearing is useless because of the crankshaft

journal wear, replace it with an undersize one referring to the
table and the figure.

(Reference)

• Undersize dimensions of crankshaft journal

9Y1210294ENS0080US0

Replacing Crankshaft Bearing 1

(When removing)

1. Press out the used crankshaft bearing 1 using a crankshaft

bearing 1 replacing tool. (Refer to "SPECIAL TOOLS".)

(When installing)

1. Clean a new crankshaft bearing 1 and crankshaft journal bore,

and apply engine oil to them.

2. Using a crankshaft bearing 1 replacing tool, press in a new

bearing 1 (2) so that its seam (1) directs toward the exhaust
manifold side. (See figure.)

9Y1210294ENS0081US0

Oil Clearance between 
crankshaft journal and 
crankshaft bearing 1

Factory specification

0.0340 to 0.114 mm
0.00134 to 0.00448 in.

Allowable limit

0.20 mm
0.0079 in.

Crankshaft journal O.D.

Factory specification

47.934 to 47.950 mm
1.8872 to 1.8877 in.

Crankshaft bearing 1 I.D.

Factory specification

47.984 to 48.048 mm
1.8892 to 1.8916 in.

Undersize

0.20 mm

0.0079 in.

0.40 mm
0.016 in.

Dimension 

A

2.3 to 2.7 mm radius

0.091 to 0.10 in.radius

2.3 to 2.7 mm radius

0.091 to 0.10 in.radius

*Dimension 

B

1.0 to 1.5 mm relief

0.040 to 0.059 in. relief

1.0 to 1.5 mm relief

0.040 to 0.059 in. relief

Dimension 

C

47.734 to 47.750 mm 

dia.

1.8793 to 1.8799 in. dia.

47.534 to 47.550 mm 

dia.

1.8715 to 1.8720 in. dia.

The crankshaft journal must be fine-finished to higher than Rmax=0.8S
*Holes to be de-burred and edges rounded with 1.0 to 1.5 mm (0.040 to 
0.059 in.) relief.

Dimension 

(A)

Factory specification

0 to 0.3 mm
0 to 0.01 in.

(1) Seam
(2) Crankshaft Bearing 1
(3) Cylinder Block

(A) Dimension

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands