manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 263

HYDRAULIC SYSTEM

G23, G26, WSM

5-S17

(EU)

Grass Collector Dump Cylinder (LD / HD)

1. Remove the snap ring (2) with a snap ring plier.
2. Push the cover (4) to the cylinder inside to make the ring (3)

free.

3. Hold the ring (3) with a minus screw driver to make it to be

dwindled, and remove the ring (3) from the cylinder sub-assy.
(9).

4. Pull out the rod sub-assy. (8) from the cylinder sub-assy. (9).
5. Remove the nut (12), the piston (10) and the cover (4).

(When reassembling)

• Do not damage the O-rings.

9Y1210294HYS0019US0

Grass Collector Lift Cylinder (HD)

NOTE

• Seal kit is adopted.

1. Drain hydraulic oil from the cylinder, and secure the tube end of

the cylinder in a vise.

2. Unscrew the cylinder head.
3. Pull out piston rod assembly from the cylinder tube.
4. Secure the rod end in a vise.
5. Unscrew the lock nut.
6. Remove the piston and cylinder head from the piston rod.

(When reassembling)

• Visually inspect the cylinder tube for signs of scoring or

damage.

• Clean the cylinder tube and piston rod assembly.
• Secure the tube end of cylinder in a vice.
• Insert the piston rod assembly to the cylinder tube, after

covering the seal with new hydraulic oil and using care not to
damage the piston seal on the piston.

• Screw the cylinder head.

(When reassembling)

• Visually inspect the cylinder tube for signs of scoring or

damage.

• Secure the rod end in a vice when tighten the lock nut.

9Y1210294HYS0020US0

Tightening torque

Self lock nut

147 to 167 N·m
15 to 17 kgf·m
108 to 123 lbf·ft

(1) Dust Seal
(2) Snap Ring
(3) Ring
(4) Cover
(5) O-ring
(6) Bush

(7) U-packing
(8) Rod Sub-assy.
(9) Cylinder Sub-assy.
(10) Piston
(11) Backup Ring
(12) Self Lock Nut

Tightening torque

Cylinder head

98.07 to 117.68 N·m
10.0 to 12.0 kgf·m
72.33 to 86.80 lbf·ft

Tightening torque

Cylinder piston mounting 
lock nut

78.46 to 98.07 N·m
8.0 to 10.0 kgf·m
57.86 to 72.33 lbf·ft

(1) Cylinder
(2) Seal Kit
(3) Nut

(4) Piston
(5) Guiding Bush (Cylinder Head)
(6) Rod

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands