manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 293

ELECTRICAL SYSTEM

G23, G26, WSM

6-S15

(EU)

Fuel Pump Continuity

1. Disconnect the 

2P

 connector from the fuel pump.

2. Check the continuity between the connector terminals with an

ohmmeter.

3. If it does not conduct, the fuel pump is faulty.

9Y1210294ELS0016US0

(10) Engine Stop Solenoid

Engine Stop Solenoid Test

1. Disconnect the 

1P

 connector from the engine stop solenoid.

2. Remove the engine stop solenoid from the engine.
3. Connect the jumper leads from the battery positive terminal to

the 

1P

 connector, and from the battery negative terminal to the

engine stop solenoid body.

4. If the solenoid plunger is not attracted, the engine stop solenoid

is faulty.

9Y1210294ELS0017US0

(11) Timer Relay

Timer Relay Connector Voltage

1. Disconnect the connector from the timer relay after turning the

main switch off.

2. Measure the voltage with a voltmeter across the connector

terminal 

4

 and chassis.

3. Turn the main switch on, and measure the voltage across the

connector terminal 

3

 and chassis.

4. If these voltages differ from the battery voltage, the wiring

harness or main switch is faulty.

9Y1210294ELS0018US0

Test of Timer Relay

1. Remove the timer relay from the tractor.
2. Connect jumper leads across the battery positive terminal and

the timer relay terminal 

3

, and across the battery positive

terminal and the timer relay terminal 

4

.

3. Connect jumper leads across the battery negative terminal and

the timer relay terminal 

2

, and across the battery negative

terminal and the bulb terminal.

4. Connect the jumper lead across the timer relay terminal 

1

 and

the bulb terminal.

5. The bulb lights up when disconnecting a jumper lead from the

terminal 

3

 arid goes off 6 to 13 seconds late, the timer relay is

proper.

9Y1210294ELS0019US0

(1) Battery (12V)

Voltage

Connector terminal 

4

 - 

chassis

Approx. battery voltage

Connector terminal 

3

 - 

chassis

Approx. battery voltage

(1) Timer Relay

(1) Timer Relay
(2) Load (Lamp)

(3) Battery (12V)

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands