manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 21

GENERAL

G23, G26, WSM

G-3

(EU)

2. GENERAL PRECAUTIONS

• When you disassemble, carefully put the parts in a clean area

to make it easy to find the parts. You must install the screws,
bolts and nuts in their initial position to prevent the reassembly
errors.

• When it is necessary to use special tools, use KUBOTA special

tools. Refer to the drawings when you make special tools that
you do not use frequently.

• Before you disassemble or repair machine, make sure that you

always disconnect the ground cable from the battery first.

• Remove oil and dirt from parts before you measure.
• Use only KUBOTA genuine parts for replacement to keep the

machine performance and to make sure of safety.

• You must replace the gaskets and O-rings when you assemble

again. Apply grease (1) to new O-rings or oil seals before you
assemble.

• When you assemble the external or internal snap rings, make

sure that the sharp edge (3) faces against the direction from
which force (2) is applied.

• When inserting spring pins, their splits must face the direction

from which a force is applied. See the figure left side.

• To prevent damage to the hydraulic system, use only specified

fluid or equivalent.

WSM000001GEG0092US0

(1) Grease
(2) Force
(3) Sharp Edge
(4) Axial Force
(5) Rotating Movement

(A) External Snap Ring
(B) Internal Snap Ring

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands