manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 291

ELECTRICAL SYSTEM

G23, G26, WSM

6-S13

(EU)

(6) Operator Presence Control (OPC) Switch

Seat Switch and Grass Collector Switch Continuity Check

1. Disconnect the 

2P

 connectors from the seat switch.

2. Remove the seat turnover switch (1).
3. Connect the circuit tester to the terminals.
4. Remove the grass collector.

(When switch is not pushed / When operator leave the seat)

1. Measure the resistance between terminals (3).
2. If continuity is not infinity, the switch is faulty. Replace it.

(When switch is pushed / When operator sits on the seat)

1. Measure the resistance between terminals (3).
2. If continuity is not 0 

Ω

, the switch is faulty. Replace it.

9Y1210294ELS0012US0

Resistance

When switch is not 
pushed / When 
operator leave the 
seat

Infinity

When switch is 
pushed / When 
operator sits on the 
seat

0 

Ω

(1) Seat Switch
(2) Grass Collector Switch
(3) Terminal
(4) Plunger

[A] LD
[B] HD

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands