manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 191

TRANSAXLE

G23, G26, WSM

2-S30

(EU)

Cylinder Block and Swash Plate

1. Remove the centre section (port block cover) mounting bolt (1).
2. Remove the O-ring (2) and the bearing (3).
3. Remove the centre section (port block cover) (6).
4. Remove the cylinder blocks (10), (12).
5. Remove the cir-clips (14), (18).
6. Remove the thrust ball bearings (15), (17).
7. Remove the swash plate (16).

(When reassembling)

• Replace the gasket between the front cover and the

transmission case with a new one.

• Replace the front gasket (5) with a new one.

9Y1210294TXS0031US0

HST Pump Shaft, HST Motor Shaft and Pinion Shaft

1. Remove the HST pump shaft (6) and the HST motor shaft (1)

from the transmission case (4).

2. Remove the gear pump idle gear (5) from the transmission case

(4).

(When reassembling)

• Put the shims on the pinion shaft and install the front cover

(HST) on the transmission case.

9Y1210294TXS0032US0

(1) Bolt (M8)
(2) O-ring
(3) Bearing
(4) Pump Shaft
(5) Front Gasket
(6) Centre Section (Port Block Cover)
(7) Motor Shaft
(8) Poppet (Charge Valve)
(9) Spring
(10) Cylinder Block (Pump)

(11) Front Cover
(12) Cylinder Block (Motor)
(13) Swash Plate Block
(14) Cir-clip
(15) Thrust Ball Bearing
(16) Swash Plate
(17) Thrust Ball Bearing
(18) Cir-clip
(19) Transmission Case

(1) HST Motor Shaft
(2) Pinion Shaft
(3) Shim

(4) Transmission Case
(5) Gear Pump Idle Gear
(6) HST Pump Shaft

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands