manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 80

GENERAL

G23, G26, WSM

G-62

(EU)

10. IMPLEMENT LIMITATIONS

The KUBOTA Machine has been thoroughly tested for proper performance with implements sold or approved by

KUBOTA. Use of implements which exceed the maximum loading weight listed below, or which are not recommended
for use with the KUBOTA Machine may result in malfunctions or failures of the machine, damage to other property
and injury to the operator or others. (Any malfunctions or failures of the machine resulting from use with improper
implements are not covered by the warranty.)

9Y1210294GEG0077US0

9Y1210294GEG0073US0

Maximum axle loading weight

MODEL

Front axle Wf

Rear axle Wr

Total gross weight

G23

400 kg (882 lbs)

850 kg (1874 lbs)

1200 kg (2646 lbs)

G26

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands