manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 219

STEERING

G23, G26, WSM

4-M2

(EU)

[2] G26 HYDRAULIC PTO CLUTCH MODEL

This model is provided with a full hydrostatic power steering.
In the full hydrostatic power steering, the steering controller is connected to the steering cylinder with only the

hydraulic piping. Accordingly, it does not have mechanical transmitting parts such as steering gear, pitman arm, drag
link, etc.. Therefore, it is simple in construction. This steering system consists of the oil strainer (2), the hydraulic pump
(3), the flow priority valve (7), the steering controller (11), the steering cylinder (12), etc..

The flow priority valve (7) located in the hydraulic control valve assembly (6) divides the oil into two directions.

One is the control flow to power steering (constantly 9.5 L/min., 2.5 U.S.gals/min., 2.1 Imp.gals/min.), and the other
is excessive flow to control valve of implement lift control.

By operating the power steering body, the required amount of oil is fed to the steering cylinder (12).

9Y1210294STM0002US0

(1) HST Pump Shaft Cylinder / 

Piston

(2) Oil Strainer
(3) Hydraulic Pump
(4) Engine
(5) Relief Valve
(6) Hydraulic Control Valve 

Assembly

(7) Flow Priority Valve
(8) Relief Valve (Oil Filter)
(9) Oil Filter
(10) Relief Valve
(11) Steering Controller
(12) Steering Cylinder
(13) Relief Valve
(14) PTO Lever
(15) Hydraulic PTO Clutch

A : To HST (Hydrostatic 

Transmission)

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands