manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 5

INFORMATION

G23, G26, WSM

I-1

(EU)

1. SAFETY FIRST

WSM000001INI0001US1

BEFORE YOU START SERVICE

• Read all instructions and safety instructions in this

manual and on your machine safety decals.

• Clean the work area and machine.
• Park the machine on a stable and level ground, and

set the parking brake.

• Lower the implement to the ground.
• Stop the engine, then remove the key.
• Disconnect the battery negative cable.
• Hang a 

"DO NOT OPERATE"

 tag in the operator

station.

WSM000001INI0010US1

START SAFELY

• Do not do the procedures below when you start the

engine.
–

short across starter terminals

–

bypass the safety start switch

• Do not alter or remove any part of machine safety

system.

• Before you start the engine, make sure that all shift

levers are in neutral positions or in disengaged
positions.

• Do not start the engine when you stay on the ground.

Start the engine only from operator's seat.

WSM000001INI0015US0

 SAFETY FIRST

• This symbol, the industry's "Safety Alert Symbol", is used throughout this manual and on labels on the

machine itself to warn of the possibility of personal injury. Read these instructions carefully.

• It is essential that you read the instructions and safety regulations before you attempt to repair or use

this unit.

 DANGER

• Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

 WARNING

• Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

 CAUTION

• Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate

injury.

IMPORTANT

• Indicates that equipment or property damage could result if instructions are not followed.

NOTE

• Gives helpful information.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands