manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 181

TRANSAXLE

G23, G26, WSM

2-S20

(EU)

Grass Collector Support Assembly

1. Disconnect the wiring harness (4) from the grass collector

support assembly (1).

2. Support the machine frame with a disassembling stand (6).
3. Remove the rear tyres (5).
4. Hook the grass collector support assembly (1) with a nylon

sling.

5. Remove the grass collector support mounting bolts (7).
6. Separate the grass collector support assembly (1) from the

machine body.

(When reassembling)

9Y1210294TXS0020US0

Tightening torque

Rear tyre mounting bolt

108.5 to 130.2 N·m
11.1 to 13.3 kgf·m
80.0 to 96.0 lbf·ft

(1) Grass Collector Support Assembly
(2) Duct
(3) Tie Rod
(4) Wiring Harness

(5) Rear Tyre
(6) Disassembling Stand
(7) Bolt

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands