manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 233

HYDRAULIC SYSTEM

G23, G26, WSM

5-M1

(EU)

1. HYDRAULIC CIRCUIT

[1] G23 (MECHANICAL PTO, LD MODEL)

The hydraulic system of this machine is composed of the hydraulic pump, the hydraulic control valve for the

mower and the grass collector, the power steering and other components.

This system has the following functions :

1. Oil is supplied by the hydraulic pump which is driven by the HST pump shaft and the idle gear in the transmission

case.
Since the hydraulic pump drive shaft is connected to the propeller shaft, the HST pump shaft and the idle gear
runs while the engine is rotating.

2. The hydraulic pump supplies the high pressured oil to the hydraulic control valve for the mower, the grass collector

and other hydraulic component parts as shown in the hydraulic circuit above after dividing the hydraulic oil by the
flow priority valve.

9Y1210294HYM0001US0

(1) Power Steering Cylinder
(2) Power Steering Controller
(3) Relief Valve (Power Steering)
(4) Oil Filter
(5) Relief Valve (Oil Filter)
(6) HST (Hydrostatic 

Transmission)

(7) HST Motor

(8) By-pass Valve
(9) Orifice
(10) Check and High Pressure 

Relief Valve (Forward)

(11) Check and High Pressure 

Relief Valve (Reverse)

(12) Charge Valve
(13) HST Pump

(14) Oil Strainer
(15) Hydraulic Pump
(16) Transmission Case
(17) Relief Valve (Main)
(18) Flow Priority Valve
(19) Hydraulic Control Valve
(20) Mower Lift Control Valve 

(Spool)

(21) Mower Lift Cylinder
(22) Grass Collector Dump Control 

Valve (Spool)

(23) Grass Collector Dump 

Cylinder

(24) Grass Collector Lift Control 

Valve (Spool)

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands