manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 197

TRANSAXLE

G23, G26, WSM

2-S36

(EU)

Hydraulic PTO Clutch 3

1. Remove the cir-clip (1).
2. Remove the backing plate (5), the disk plates (6), and the

separate plates (7) from the clutch case (3).

3. Remove the cir-clip (9) and the oil seal (8).
4. Remove the cir-clip (10) and the front PTO shaft (2) from the

rear case (4).

5. Remove the cir-clip (11) and the ball bearing (12) from the front

PTO shaft (2).

(When reassembling)

• Do not damage the oil seal.
• Install the disk plates and the separate plates to the original

positions.

9Y1210294TXS0054US0

(1) Cir-clip
(2) Front PTO Shaft
(3) Clutch Case
(4) Rear Case
(5) Backing Plate
(6) Disk Plate

(7) Separate Plate
(8) Oil Seal
(9) Cir-clip
(10) Cir-clip
(11) Cir-clip
(12) Ball Bearing

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands