manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 214

FRONT AXLE

G23, G26, WSM

3-S8

(EU)

(2) Disassembling Front Axle

Kingpin and Bush

1. Remove the split pins (3) and the nuts (2).
2. Remove the power steering cylinder mounting bolts (M10).
3. Remove the power steering cylinder assembly (4) from the front

case assembly(8).

4. Remove the cir-clips (1) and the kingpins (5), (9) from the front

case assembly (8).

5. Remove the bushes (6), (7), (10) from the front case assembly

(8).

(When reassembling)

• Apply grease to the grease fittings and the bushes.

9Y1210294FAS0009US0

Tightening torque

Tie-rod end nut

17.7 to 34.3 N·m
1.8 to 3.5 kgf·m
13.1 to 25.3 lbf·ft

(1) Cir-clip
(2) Nut
(3) Split Pin
(4) Power Steering Cylinder Assembly
(5) Kingpin (RH)

(6) Bush
(7) Bush
(8) Front Case Assembly
(9) Kingpin (LH)
(10) Bush

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands