manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 327

MOWER

G23, G26, WSM

7-S14

(EU)

Centre Case

1. Turn the bearing shaft (4) to take out the locating ball (10).
2. Take out the locating ball (10).
3. Remove the bearing shaft (4) from the centre case (6).
4. Remove the gear and mark the identification mark with the paint

as shown in the picture.

5. Remove the other component parts from the centre case (6).

(When reassembling)

• Do not lose the locating balls.
• Install the locating balls to the original position securely.

9Y1210294MOS0014US0

(1) Ball Bearing
(2) Bearing LH Gear
(3) Ball Bearing
(4) Bearing Shaft
(5) Cir-clip
(6) Centre Case
(7) Bearing

(8) Cir-clip
(9) Bearing RH Gear
(10) Locating Ball

A : Paint Mark
B : RCK54-G26

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands