Kubota G23 Workshop Manual Download Page 288

Page: 288 / 343

ELECTRICAL SYSTEM

G23, G26, WSM

6-S10

(EU)

(3) Starter

Motor Test

NOTE

• Secure the starter to prevent it from jumping up and down

while testing the motor.

1. Disconnect the battery negative cable from the battery.
2. Disconnect the battery positive cable and the leads from the

starter.

3. Remove the starter from the engine.
4. Disconnect the connecting lead (2) from the starter

terminal

(1).

5. Connect a jumper lead from the connecting lead (2) to the

battery positive terminal post.

6. Connect a jumper lead momentarily between the starter motor

housing and the battery negative terminal post.

7. If the motor does not run, check the motor.

WSM000001ELS0009US0

Magnet Switch Test (Pull-in, Holding Coils)

1. Remove the motor from the start housing.
2. Prepare a 6 V battery for the test.
3. Connect jumper leads from the battery negative terminal to the

housing and the starter

terminal.

4. The plunger should be attracted and the pinion gear should pop

out when a jumper lead is connected from the battery positive
terminal to the

terminal. It's a correct.

5. Disconnect the jumper lead to the starter

terminal. Then the

pinion gear should remain popped out. It's a correct.

IMPORTANT

• Testing time must be 3 to 5 seconds.

9Y1210294ELS0008US0

(4) Glow Plug

Lead Terminal Voltage

1. Disconnect the wiring lead (2) from the glow plug (1) after

turning the main switch off.

2. Turn the main switch key to the "

PREHEAT

" position, and

measure the voltage between the lead terminal and the chassis.

3. Turn the main switch key to the "

START

" position, and measure

the voltage with a voltmeter between the lead terminal and the
chassis.

4. If the voltage at either position differs from the battery voltage,

the wiring harness or main switch is faulty.

9Y1210294ELS0009US0

(1)

Terminal

(2) Connecting Lead

C : C Terminal
S : S Terminal

(a) To Negative Terminal
(b) To Positive Terminal

Voltage
(Lead terminal –
Chassis

Main switch key at

"PREHEAT"

Approx. battery voltage

Main switch key at

"START"

Approx. battery voltage

(1) Glow Plug

(2) Wiring Lead (Positive)

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands

Kubota G23, Workshop Manual

Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands