manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 40

GENERAL

G23, G26, WSM

G-22

(EU)

[3] CHECK POINTS OF EVERY 50 HOURS

Checking Safety Devices

The Safety Device in your machine are designed to protect you

while operating. Please check these Safety Devices periodically -
daily is best - to test function of the Safety Devices before operation.

 CAUTION

To avoid personal injury :

• Do not allow anyone near the machine while testing.
• If the machine does not pass one of the following tests, do

not operate the machine.

IMPORTANT

• Check the following tests before operating the machine.

Q

Checking Safety Devices

1. Check the following tests before operating the mower.

Sit on the operator's seat for all tests.

2. If the machine does not pass one of the following tests, do not

operate the machine.

Q

Safety Start Control 1

1. Depress the brake pedal fully.
2. Engage the PTO lever.
3. Turn the key switch to the 

"START"

 position.

4. The engine should not crank.

Q

Safety Start Control 2

1. Disengage the PTO lever.
2. Release the brake pedal.
3. Turn the key to the 

"START"

 position.

4. The engine should not crank.

Q

Seat Safety Control 1

1. Run the engine at half throttle.
2. Engage the PTO lever.
3. Stand up. (DO NOT GET OFF THE MACHINE.)
4. Engine should shut off.

Q

Seat Safety Control 2

1. Run the engine at half throttle.
2. Disengage the PTO lever.
3. Release the brake pedal.
4. Stand up. (DO NOT GET OFF THE MACHINE.)
5. Engine should shut off.

Q

PTO Safety Control 1

1. Dismount the container from the platform.
2. Run the engine at half throttle.
3. Engage the PTO lever.
4. Engine should shut off.

Q

PTO Safety Control 2

1. Run the engine at half throttle.
2. Engage the PTO lever.
3. Dump or lift up the grass catcher.
4. Engine should shut off.

9Y1210294GEG0023US0

(1) PTO (Clutch) Lever
(2) Brake Pedal

[A] G23
[B] G26

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands