manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 259

HYDRAULIC SYSTEM

G23, G26, WSM

5-S13

(EU)

Grass Collector Dump Cylinder (HD)

1. Remove the grass collector from the machine. (Refer to "Grass

Collector" section.)

2. Remove the frames (1), (2), (3), (4) as shown in the pictures.
3. Remove the bottom plate (5).
4. Disconnect the rotation hoses (7), (8).
5. Remove the cylinder shaft (12) and the joint pin (14).
6. Remove the grass collector dump cylinder (6).

(When reassembling)

• Connect the rotation hose to the original position.

9Y1210294HYS0013US0

(1) Bag Frame (RH)
(2) Rear Frame
(3) Front Bag Frame
(4) Bag Frame (LH)
(5) Bottom Plate
(6) Dump Cylinder
(7) Upper Rotation Hose

(8) Lower Rotation Hose
(9) Cylinder Collar
(10) Split Pin
(11) Plain Washer
(12) Cylinder Shaft
(13) Connector Comp.
(14) Joint Pin

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands