manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 105

ENGINE

G23, G26, WSM

1-S23

(EU)

Nozzle Holder

1. Secure the nozzle retaining nut (7) with a vise.
2. Remove the nozzle holder (1), and take out parts inside.

(When reassembling)

• Assemble the nozzle in clean fuel oil.
• Install the push rod (4), noting its direction.
• After assembling the nozzle, be sure to adjust the fuel injection

pressure.

9Y1210272ENS0028US0

[2] DISASSEMBLING AND ASSEMBLING

(1) Separating Engine

Draining Engine Oil

1. Start and warm up the engine for approx. 5 minutes.
2. Place an oil pan underneath the engine.
3. Remove the drain plug (1) to drain oil.
4. After draining, screw in the drain plug (1).

(When refilling)

• Fill with the new oil up to the upper line on the dipstick (4).

IMPORTANT

• Never mix two different types of oil.
• Use the proper SAE Engine Oil according to ambient

temperatures.

• Refer to "LUBRICANTS, FUEL AND COOLANT" (See page

G-9).

9Y1210294ENS0018US0

Tightening torque

Nozzle holder

35 to 39 N·m
3.5 to 4.0 kgf·m
26 to 28 lbf·ft

Overflow pipe nut

20 to 24 N·m
2.0 to 2.50 kgf·m
15 to 18 lbf·ft

Nozzle holder assembly

49 to 68 N·m
5.0 to 7.0 kgf·m
37 to 50 lbf·ft

(1) Nozzle Holder
(2) Adjusting Washer
(3) Nozzle Spring
(4) Push Rod

(5) Distance Piece
(6) Nozzle Piece
(7) Nozzle Retaining Nut

Engine oil capacity

Capacity

G23

3.1 L
3.3 U.S.qts
2.7 lmp.qts

G26

3.5 L
3.7 U.S.qts
3.1 lmp.qts

(1) Drain Plug
(2) Front Tyre
(3) Oil Inlet
(4) Dipstick

A : Oil level is acceptable within this 

range

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands