manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 201

TRANSAXLE

G23, G26, WSM

2-S40

(EU)

Backlash between Spiral Bevel Pinion Gear and Bevel Gear

1. Temporarily assemble the spiral bevel pinion gear (1) and the

bevel gear (2) in the transaxle case.

2. Prepare the fuse bent already three to four times.
3. Hold the fuse on the bevel gear teeth upper surface 

"A"

.

4. Turn the front drive shaft one turn clockwise by hands.
5. Measure the thickness of the fuse as a backlash between the

spiral bevel pinion gear and the bevel gear.

6. If the back lash exceeds the factory specifications, adjust the

shims (4).

9Y1210294TXS0044US0

(3) Brake Case

Flatness of Actuator and Bearing Holder

1. Place a straightedge of 150 mm (5.91 in.) or more in length on

the contacting surface of the actuator and the bearing holder.

2. Inspect the friction surface of the actuator and the bearing

holder with the straightedge, and determine if a 0.30 mm
(0.0118 in.) feeler gauge will fit on the part of wear.

3. If it will fit, resurface.

9Y1210294TXS0045US0

Backlash between spiral 
bevel pinion and bevel 
gear

Factory specification

0.10 to 0.30 mm
0.0040 to 0.011 in.

(1) Pinion Gear
(2) Bevel Gear
(3) Shim
(4) Shim

A : Bevel Gear Teeth Upper Surface

Flatness of actuator and 
bearing holder

Allowable limit

0.30 mm
0.0118 in.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands