manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 210

FRONT AXLE

G23, G26, WSM

3-S4

(EU)

4. CHECKING, DISASSEMBLING AND SERVICING

[1] CHECKING AND ADJUSTING

Toe-in

1. Inflate the front tyres to the specified pressure.
2. Turn the front wheels straight ahead, and measure the toe-in

(

B-A

).

3. If the measurement is not within the factory specifications,

charge the tie-rod length to adjust.

IMPORTANT

• After adjusting the toe-in, secure the tie-rod with the lock

nut.

9Y1210294FAS0004US0

Front Axle Rocking Force

1. Jack up the front side of machine and remove the front wheel.
2. Set a spring balance to the front axle kingpin (3).
3. Measure the front axle rocking force.
4. If the measurement is not within the factory specifications,

adjust as following.

Q

Adjusting procedure

1. Remove the split pin (2). Push and pull the kingpin (3) with a

push pull gauge.

2. Tighten or loosen the adjusting nut (1) so that the measurement

of rocking force comes to factory specifications.

3. If the slot and pin hole do not meet, align the nut until they do

meet within factory specifications.

4. Install the new cotter pin.

(When reassembling)

• Be sure to split the cotter pin like an anchor.

(Reference)

• Tightening torque of adjusting nut :

20 N·m (2.0 kgf·m, 14 lbf·ft)

9Y1210294FAS0005US0

Toe-in (

B-A

)

Factory specification

0 to 5 mm
0 to 0.2 in.

A : Wheel to Wheel Distance at Front B : Wheel to Wheel Distance at Rear

Front axle rocking force

Factory specification

20 to 300 N
2.0 to 30.0 kgf
4.4 to 67.5 lbf

(1) Adjusting Nut
(2) Split Pin
(3) Kingpin

A : Jack Up
B : Front Axle Rocking Force

(Pushing and Pulling)

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands